A mallet is one of the small items that virtually every person or family needs. However, not many people realize that they need a mallet until there’s some work that needs to be done and it is required.
One good thing with the wooden mallet is that, it is simple to make and is suitable for many hammering needs in a home or shop. Due to its simplicity in nature, one can easily craft it as a hobby. When making a wooden mallet, you need to have a number of tools that will make your work easier. To successfully complete mallet project woodturning tools are important; you require parting tool, skew, caliper and a roughing gouge. All these can be obtained from www.yourwoodturningtools.com.
When making a mallet, you will require a length wood of about 6” long by 3 1/4" square for the mallet head, and another piece with a length of 12" and width of 1 1/4" square for the handle. The next step you now need to do to is to mark the center of both ends of these pieces of wood to locate the center. This is easily done by measuring from corner to corner, where the lines cross is the center. Mount the large square to the wood lathe using the located centers to align the piece.
Rotate the mallet head by hand, this is meant to test the blank’s stability and alignment on the wood lathe before you switch on the lathe, and begin turning the mallet. As the wood becomes rounded and balanced you can increase its speed gradually, higher speed will result in a smoother cut. With the help of calipers insure that the wood has an even diameter along the length of the piece. Use the parting tool to locate both ends of the mallet head, you should leave a short tendon then remove with a saw
You can now make some decorative patterns close to both ends of the blank, and then release the blank from the wood lathe. Use a saw to cut off the remaining tendons. You now need to precisely drill a hole in the center of the mallet head where the handle will be fitted into. To do this, you can us a drill press to drill the hole for the handle. Make a jig to hold the mallet head to keep the head stable, usually a large “V” notch in another piece of wood will suffice to hold the round head. Drill a vertical hole for the handle in the center, both end to end and side to side.
The next step is to make the mallet handle. Mount the small square wood into the wood lathe, the procedure is the same as for the mallet head. Use the roughing gouge, round the blank and shape the handle to your personal design. Ensure that the handle diameter meets your requirements; fits your hand. Create a short tendon to match the diameter of the hole you drilled into the mallet head. The tendon should have a slight taper, from smaller than the drilled hole to larger than the drilled hole, this will insure a tight fit. Again remove the tendons with a saw.
Both the Mallet head and Handle have been sanded and the tendons removed you can how glue the two pieces together. After the glue is dry apply a coat of oil to preserve the mallet. Mineral Oil, Linseed Oil, Tung Oil, or whatever you would like, I shy away from varnish as it tends to be slick and makes a good grip difficult.
Woodturning Tools, Projects, Wood, Wood Lathe, Craft, Hobby
Segmented Bowl
I’ve been planning to turn a segmented bowl with using several species of wood glued together to form a pattern as one of your many projects, here are a few tips and hints on doing just that. If you’re serious about your woodworking hobby, then you’ve probably goggled the subject and seen images of all the amazing things.A Turning Project
If you’ve been planning on experimenting with using several species of wood glued together to form a pattern as one of your many projects, here are a few tips and hints on doing just that. If you’re serious about your woodworking hobby, then you’ve probably Googled the subject and seen images of all of the amazing things that other people who love to craft stuff from wood have made using this particular woodworking method. Some of them are quite amazing and your project can be, too!Woodturning A Wooden Bowl
It is always fun for any wood turner to turn logs of wood from their own environment into a good rich, looking usable utensils or into various forms of art that easily shows the turner’s skill. Some of those woodturning projects are considered difficult, include turning wood bowls. Successful creation of these bowls requires a lot of attention to details. I usually craft bowls as my hobby, utilizing many different species of trees and grain patterns as I can find.