Direct Gas-Fired Make-up Air Units supply tempered and filtered air to the indoor environment. In summer, a direct-fired unit may be used as an air handler, with the heater disabled. By adding a DX or...
Direct Gas-Fired Make-up Air Units supply tempered and filtered air to the indoor environment. In summer, a direct-fired unit may be used as an air handler, with the heater disabled. By adding a DX or evaporative cooling section to the unit, it may be used to supply conditioned air year round.
ABB Blower Co. offers different types of Industrial Make-Up Air Systems for larger industrial plants ventilation needs.
Negative Air Pressure in industrial manufacturing facilities can create problems such as:
- Exhaust fans losing performance, as the building pressure becomes negative.
- Pilot light outages and exhaust system failure on natural draft gas equipment.
- Cold air drafts and infiltration of dirt and contamination from outside.
- Difficulty opening or closing exterior doors.
Headaches and nausea among personnel due to inadequate ventilation. In temperate climates or during mild weather, moderate amounts of make-up air can be supplied by simply opening windows or overhead doors. However, this is usually not the case in industrial and commercial facilities. Forced ventilation Make-up air is required.
Make-Up Air Applications include:
There are three general applications for Make-Up Air Units:
- Direct Compensating Ventilation
- General Area Ventilation
- Door Heating
Direct Compensating Ventilation.
Conditioned Air is Delivered to the Immediate Vicinity of Exhaust. This is the case for welding fume extractors, stovetop exhaust hoods, paint booths, or similar applications.
General Area Ventilation.
Conditioned Air Blankets Entire Area of Building to Compensate for Many Exhausts. Introduced in Cleanest Part of Building - Flows to Negative Pressure Areas - Picks up Dust, Vapors, and Odors en route.
Door Heaters
Heated Air is introduced at open doors to warm incoming air or compensate for loss. Heater may also be used as part of an “air door” system.
Typical Industrial Uses:
* Plating Tanks
* Paint Spray Booths
* Welding Operations
* Chemical Exhaust
* Degreasing
* Factory Ventilation
* Plastic Molding
* Foundry Works
* Grinding & Buffing Operations
Typical Commercial Uses:
* Warehouses
* Kitchens
* Entryways
* Gymnasiums
* Pools
* Exposition Buildings
* Garages
While there are no facts and figures to show how many buildings in the United States provide the correct amount of makeup air, it can be surmised that there are probably a great many that do not have sufficient makeup air. And there's no one solution that is available for every building. Each building must be analyzed with a careful air balance calculation and evaluated based on the diversity of sources of exhaust air and infiltration.
Make-Up Air Volume Requirements:
The recommended method for calculating Make-up Air Volume is to determine the total CFM capacity of exhaust fans, blowers, stacks, etc. in the building and add 10%. This will create a positive pressure in the building ventilating.com fanblower.com highpressureblower.net industrialblowerfan.com industrialfanblower.net industrialfanblower.com pressureblower.net northernindustrialsupplycompany.com industrialpressureblower.com tenderall.com chicagoblowercanada.com cbblower.com buffaloblower.com buffalofan.com nis-co.com canadianblower.com olegsystems.com canadablower.com abbblower.com acmefan.net industrialblower.net fansandblowers.net americanblower.net barryfan.com cincinnatifan.net canadafans.com barryfan.net greenheck.net pennbarry.net pennfan.net tcffan.co
.
When information is not available, the following estimates may be used to determine approximate requirements:
- Paint / Spray Booth: 100 to 200 CFM per sq. ft. of face opening.
- Oven Exhaust: One air change per minute.
- Fume Exhaust: Area of Pipe (in square feet) x velocity (3,000 feet/min average) = CFM.
- Roof Ventilator: same as Fume Exhaust.
- Canopy Hoods: 100 to 300 CFM per square foot of hood open area.
- Furnace Combustion Air: Minimum CFM = BTU/hr rating / 6,000.
- Drying, Baking, Curing Ovens: 100 CFM per square foot of booth cross section.
- Pickling or Cleaning Tanks: 150 CFM per square foot of door opening or 200 CFM per square foot of hood face opening.
Additional information can be found at the ABB Blower company web site http://www.abbblower.com/products/centrifugal_wall_roof_ventilators.html
Susann Terlitski
Air Handling Units (AHU) Engineer
ABB Blower Co.
nis@primus.ca
http://www.abbblower.com/products/utility_fans.html
http://www.abbblower.com/products/pedestal_air_circulators.html
Industrial Direct-Fired Airhandling Units
In industrial environments where there is a high density of employees and many manual operations involved, an improvement in the environment can produce substantial benefits in terms of increased production, reduced errors, and a decline in complaints and absenteeism among employees.
Proper Building Ventilating
A proper ventilation system for a roof is often the single most important factor which governs its longevity. A roof having a good ventilation system, along with proper maintenance will live approximately 25% more than any other roof.
Squirrel Cage Blower Selection
We frequently here a question like this one: I have a squirrel cage blower and I'd like to build an air filter for my shop, but the blower doesn't have any markings so I don't know how much air it will move. How can I determine the CFM of the blower, and will the CFM affect the size of the filter I should use? It would seem the more air you're moving, the more square inches of filter you should have, or does it really matter ?
